11" tall x 1.5" thick EPS Foam Flash Dancer cut out

Insert a toothpick or bamboo skewer to insert into a foam base.

Use only water based non-petroleum products. Spray paint can eat the foam.

Contact us if you need the items finished with a color, larger, or custom shapes.

Use foam cut outs for a dance themed party decorations.



**Disclaimer: There may be cut lines in some figures where the hot wire needed an entry & exit line to get into the center of a figure to finish cutting the shape. This line is 1/8th of an inch wide. Use paint spackle or masking tape to cover cut lines when painting &/or glittering. Spackle works better if your just painting. The glitter hides the masking tape better.

11" tall x 1.5" thick Glittered Dancer with hat
Use a toothpick or bamboo skewer to insert into a foam base.  Base not included.
Use only water based non-petroleum products. Spray paint can eat the foam.


Use cut outs for a dancer themed party decorations.

**Disclaimer: There may be cut lines in some figures where the hot wire needed an entry & exit line to get into the center of a figure to finish cutting the shape. This line is 1/8th of an inch wide. Use paint spackle or masking tape to cover cut lines when painting &/or glittering. Spackle works better if your just painting. The glitter hides the masking tape better.

11.5" tall x 1.5" thick white Glittered Dancer cut out

Use a toothpick or bamboo skewer to insert into a foam base.  Base not included.

Use only water based non-petroleum products. Spray paint can eat the foam.

Use cut outs for a dancer themed party decorations.

11" tall x 1½" thick EPS Foam Break Dancer.

Use toothpick or bamboo skewer to insert into a foam base.

11" tall x 1.5" thick EPS Foam Dancer Waving cut out
Insert toothpick or bamboo skewer to attach to a foam base.

Use only water based non-petroleum products. Spray paint can eat the foam.

Use EPS Foam cut outs for a dancer themed party decorations.

White Unfinished EPS Foam. 11"tall x 1.5" thick.

Use a toothpick or bamboo skewer to insert into a foam base.  Base not included.

Create your own custom decorations with our Unfinished Break Dancer Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Create your own custom decorations with our Unfinisheda Dancer Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Create your own custom decorations with our Unfinished Gymnastics Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Create your own custom decorations with our Unfinished Dancer Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Create your own custom decorations with our Unfinished Hip Hop Dancer Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Create your own custom decorations with our Unfinished Dancer Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Create your own custom decorations with our Unfinished Gymnastics Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Create your own custom decorations with our Unfinished Dancing Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Create your own custom decorations with our Unfinished Dance Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for recitals and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________