High Top Tennis Shoe shape cut out of EPS foam.
Available 9 inch or 11-inch-long x 1.5 inches thick. The height is proportional to the length.

The High-Top shoe is 9-inch-long x 1.5 inches thick sitting on a 6-inch diameter glittered disc. The finished Centerpiece Height - 10-inches.

The first color selection is the color of the shoe.  The second color selection is for the accents on the shoe and the disc it sits on.

The shoes are glittered with a loose glitter that will come off even though we brush and seal it.

The centerpieces are shipped in separate pieces for you to assemble by inserting the attached picks into the base.
. 

Create your own custom decorations with our Unfinished Sports Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for sports banquets and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________

Tennis Player Cutout, perfect for DIY table centerpieces or party decorations. Each standee measures approximately 11" tall with the width proportional to the height. Made from 1.5" thick EPS foam, these cutouts are lightweight, durable, and offer depth that paper or cardboard can’t offer. They are self-supporting, but because they are lightweight, they may tip if the table is bumped. For extra stability, we recommend inserting them into a foam base.

✨ Glittered Cutouts: Fully coated in glitter; some flaking is normal. To reduce flaking, you can apply multiple coats of brush-on Mod Podge in gloss finish. Do not use other sealers, which may damage the foam.

🎨 Unfinished Cutouts: For DIY painting, decorating, or adding glitter. Use only water-based, non-petroleum paints, glues, or coatings. Do NOT use spray paint or aerosol sealers, to avoid melting the foam. Minor cut lines from the hot wire may be present; fill with paintable latex caulk before decorating.

Tennis Player Cutout, perfect for DIY table centerpieces or party decorations. Each standee measures approximately 11" tall with the width proportional to the height. Made from 1.5" thick EPS foam, these cutouts are lightweight, durable, and offer depth that paper or cardboard can’t offer. They are self-supporting, but because they are lightweight, they may tip if the table is bumped. For extra stability, we recommend inserting them into a foam base.

✨ Glittered Cutouts: Fully coated in glitter; some flaking is normal. To reduce flaking, you can apply multiple coats of brush-on Mod Podge in gloss finish. Do not use other sealers, which may damage the foam.

🎨 Unfinished Cutouts: For DIY painting, decorating, or adding glitter. Use only water-based, non-petroleum paints, glues, or coatings. Do NOT use spray paint or aerosol sealers, to avoid melting the foam. Minor cut lines from the hot wire may be present; fill with paintable latex caulk before decorating.

Create your own custom decorations with our Unfinished Sports Foam Cutout. Each shape measures 11 inches tall, with the width proportional to the design, and is cut from 1.5" thick EPS foam.

Perfect for table centerpieces for sports banquets and all special occasions

Foam cutouts are lightweight and self-supporting. For extra stability, we recommend inserting them into a foam base.

Decorating Tips

• Use water-based paints such as acrylic or tempera.
• For glitter application, mix paint and school glue in a 50/50 ratio, apply to the surface, and cover with glitter while wet.

Important Information

• Use water-based, non-petroleum paints and adhesives only.
• Spray paint may melt or damage EPS foam and should not be used.
• Always test new products on a small area first.
• Hot wire cut lines may be visible and can be filled with paintable latex caulk before decorating.

Attaching to a Foam Base
Insert a toothpick or bamboo skewer into the shape, remove it, add glue to the hole, and reinsert the skewer. Use same procedure for inserting it into the base.

✔ Lightweight yet sturdy
✔ Easy to paint and decorate
✔ Perfect for DIY centerpieces and party decor

________________________________________